Function overview
MC 2.0 WL / WR?
|
WL (=wireless) Digital wireless transmission
|
WR (=wired) Wired transmission
|
Recommended use
Downhill
Freeride
X-Country
Marathon
Road Bike
Track cycling
Tours/Trekking
City
Commuting
The new MC 2.0 is available in two versions. As a wired model in the WR version or a wireless model in the WL version. The wireless model has a digital two-channel receiver. The MC 2.0 WL can therefore simultaneously receive and display either speed + heart rate or speed + cadence.
The new MC 2.0 offers:
- Either
- altitude measurement + heart rate or
- altitude measurement + cadence*
- Simple use
- Everything in view, the most important details on display at once
- Digital wireless transmission for
- speed + heart rate or
- speed + cadence
- Menu system for settings
- Display backlight
- Data storage during battery replacement
- Battery warning when the battery is weak
- 2 home altitudes, adjustable
- Stopwatch direct access
- Altitude correction during transport
- Altitude measurement uphill and downhill
- For dealers: Adjustable via SSB
* Heart rate + cadence option available on the wireless version MC 2.0 WL only
All functions with full details and as a comparison
Altitude functions
Altitude correction during transportation
The MC 2.0 has a transport function, which corrects the current altitude automatically, when the MC 2.0 is for instance transported in the car (for this the MC 2.0 must be in the handlebar bracket).
Select home altitude
Via the short-cut button
the home altitude can be selected or the current altitude adjusted directly.
- Two selectable home altitudes
- Current altitude can be set in meters or sea level pressure
The new MC 2.0 makes altitude measurements both UPHILL and DOWNHILL.
All altitude functions are on the button “ALTI”. The functions are accessed by pressing the button sequentially.
All altitude functions
- Uphill altitude difference, for current trip
In the submenu:
– Uphill altitude difference total bike 1 / bike 2
– Uphill altitude difference total (bike 1 + bike 2) - Maximum altitude of a trip
In the submenu:
– Maximum altitude of all trips with bike 1 / bike 2 - Average ascending gradient of a trip, in percentage
- Maximum ascending gradient, in percentage
- Downhill altitude difference, for current trip
In the submenu:
– Downhill altitude difference total for bike 1 / bike 2
– Downhill altitude difference total (bike 1 + bike 2) - Average descending gradient of a trip, in percentage
- Maximum descending gradient of a trip, in percentage
In addition, permanently shown in the display:
- Current altitude
- Current gradient uphill / downhill
- Current temperature
Two configurable start altitudes
The MC 2.0 can use two different start altitudes. For example, one start altitude can be the home start altitude. The second start altitude could be the start altitude on holiday. If these start altitudes have been set, recalibration before starting the next trip is quick and easy.
More on 'recalibration'.
Heart rate functions
Training zones
3 training zones can be selected in the MC 2.0 WL:
- The FIT and FAT zones are automatically calculated from the set personal data and from the personal maximum HR.
- The values for the OWN zone are similarly calculated, but can be adjusted individually.
Direct selection
The training zone can be selected directly via a short-cut button:
Press and hold the HR/CAD button
With MC 2.0 WL, either heart rate data or cadence data can also be displayed. In a selection menu it is defined whether heart rate, cadence or no other information should be displayed.
All heart rate functions are located on the button HR / CAD. The heart rate / cadence functions can be accessed sequentially by pressing a button.
Heart rate functions
- Average / maximum heart rate on the current trip
- Calories burnt on current trip
- Time when the heart rate
- was below the set lower limit
- was in the set training zone
- was above the set upper limit
A beeper emits a signal when the current heart rate exceeds the set upper limit or is below the set lower limit. The beeper can be turned off.
Indicators
For heart rate measurement, the indicators show wether the heart rate is:
- below the lower limit
- above the upper limit
- in the selected training zone
Cadence
Indicators
When measuring the cadence, indicators again show whether the cadence
- was below the set lower limit
- in the set training zone
- was above the set upper limit
With MC 2.0 WL, either heart rate data or cadence data can also be displayed. In a selection menu it is defined whether heart rate, cadence or no other information should be displayed.
All cadence functions are located on the button HR / CAD. The heart rate / cadence functions can be accessed sequentially by pressing a button.
Cadence functions
- Average / maximum cadence on the current trip
- Time when the cadence
- was below the set lower limit
- was in the set training zone
- was above the set upper limit
In addition, the cadence will be permanently shown on the display.
Temperature
Celsius <> Fahrenheit
The temperature unit can be changed in the setting menu (press and hold the M button) under 'DIMENSION Setting' (change by pressing ALTI or HR/CAD).
Here, you can sequentially enter the units for:
- speed
- altitude
- temperature and
- weight
and gradually confirm your selections by pressing the M button.
The current temperature is permanently shown at the top left of the display. The settings can be used to switch between Celsius and Fahrenheit.
Visible at all times
In addition to the speed, current altitude, ascent/descent plus the temperature is always shown on the display.
Stopwatch
Direct access
Your direct access for the stopwatch:
>> ALTI + HR / CAD
3-2-1 Start
Press a button and the stopwatch is in the display ... and it runs. The MC 2.0 has a direct access to the stopwatch, whereby you can access it from any function by pressing a button.
The stopwatch is on the display immediately and runs or is stopped.
Settings
Changing the unit of measurement
Press and hold the MENU button – press HR/CAD to navigate to 'DIMENSION' and confirm the selection by pressing MENU.
Press the ALTI or HR/CAD buttons to select the unit of measurement for:
- Speed
- Altitude
- Temperature
- Weight
Confirm each unit by pressing MENU then edit the next unit.
Wheel size via tyre table
Press and hold the MENU button – press HR/CAD to navigate to 'WHEEL SIZE' and confirm the selection by pressing MENU.
Press the ALTI or HR/CAD buttons to select 'WHEEL 1' - MENU - ALTI - TYRE SELECT - MENU.
Select the applicable value and confirm the selection by pressing MENU.
Setting the unit of measurement
All units on the MC 2.0 can be adapted to local conditions as desired.
Wheel size setting via tyre table
With the MC 2.0, the wheel size can optionally be selected using a tyre table or, as before, set in millimeters or inches. Thus the wheel size setting is even more convenient.
